Components ()
View all results.
Categories ()
View all results.
Searching...
Sorry, we couldn't find anything for that search.
Recent Searches.
Return to Washers & Spacers
- of components found

No products match the filters selected.

Please clear the filters and try again.
No Results
Dowty Washers

What are Dowty Washers?

Dowty washers, also known as Dowty seals or bonded sealing washers, are part of Accu's Washers & Spacers range and create a leak-tight seal on threaded connections carrying oil, fuel or compressed air under pressure. Each one is a flat steel ring with a nitrile rubber seal bonded to its inner edge. On these self-centring versions, a thin rubber lip extends into the bore, so the hole looks noticeably smaller than the thread it is made for. Because the steel carries the clamping load and the rubber does the sealing, one washer gives a dependable face seal on parallel threads, which cannot seal on their own.

That makes Dowty washers a fixture of hydraulic and pneumatic systems, where they seal pump, valve and cylinder ports. In automotive work they seal fuel line unions and oil drain plugs. The range is RoHS and REACH compliant, with certificates of conformity available.

How Dowty Washers Work

A Dowty washer fits under the head or collar of a bolt, plug or fitting, sitting between it and the spot face around a threaded port. Before tightening, the rubber stands proud of the 1.5 mm steel ring. As the fastener is torqued down it’s squeezed between the two faces until both meet the steel. From that point the steel carries the clamping load, which protects the rubber from over-compression and stops system pressure extruding it outwards. On a self-centring design, the inner lip grips the thread during assembly and holds the seal concentric with the port, so the rubber is compressed evenly all the way round rather than pinched on one side.

Take a hydraulic power unit as an example. Its valve manifold often carries gauge and test ports that are not needed in service, and these are blanked off with hexagon head plugs, each with an M16 Dowty washer on the thread under its collar. The lip holds the washer in place while the fitter offers the plug up to the port, and tightening compresses the rubber against the manifold's spot face. Without that face seal, oil under pressure tracks along the clearance in the parallel thread and weeps from the port, leaving a film of oil that collects dirt and a reservoir that slowly needs topping up.

Materials Dowty Washers Are Made From

Accu's bonded sealing washers combine two materials in one component, each chosen for the job it does in the joint:

  • Steel / Rubber - NBR: The steel ring carries the clamping load and sets the final compression of the seal, while the shore 80A nitrile rubber resists mineral oils, mineral-based hydraulic fluids, petrol and diesel. Nitrile is not suited to glycol-based brake fluids, ketones or prolonged exposure to sunlight and ozone.

Every size has a natural finish, meaning the steel ring is uncoated, so the range suits oil-filled systems and dry, indoor environments rather than applications exposed to water or weather.

Sizes & Types of Dowty Washers Available

Accu's range of Dowty washers is available in five metric sizes to suit common hydraulic, pneumatic and automotive ports:

  • Thread Size: M8 (8 mm) to M20 (20 mm).
  • Internal Diameter (ID): 6.4 mm to 16.8 mm.
  • External Diameter (OD): 14 mm to 28 mm.
  • Uncompressed Height (H): 2.1 mm to 2.3 mm.
  • Washer Thickness (T): 1.5 mm.

The five sizes are M8, M10, M12, M16 and M20, so there is no M14 or M18 option and nothing smaller than M8. The internal diameter is smaller than the thread in every size because it is measured across the self-centring lip, not a clearance bore. Washer thickness is a constant 1.5 mm. The range is not made to a published standard, so check the external diameter against the port's spot face before specifying.

For blanking ports across the same M8 to M20 span, Accu's Metric Hexagon Head Pipe Plugs to DIN 910 pair naturally with these washers. Where a rubber seal is not wanted, Copper Washers offer an all-metal alternative that seals by deforming under load. For wet or outdoor applications where uncoated steel would corrode, Sealing Washers pair stainless steel with an EPDM seal, though EPDM is not suited to mineral oils. Below M8, Sealing Screws With O-Rings build the seal into the screw itself.

FAQ

Q: What are bonded washers used for?

A: Bonded washers seal threaded connections that carry fluid or air under pressure, sitting under the head of a bolt, plug or fitting where it seats against a port. They are common on hydraulic pump, valve and cylinder ports, on pneumatic fittings and in automotive applications such as fuel line unions and oil drain plugs.

Q: Are Dowty washers any good?

A: For sealing parallel threaded ports, yes. Bonding the rubber to a steel ring increases its resistance to bursting and removes the need to machine a groove to retain the seal, as an O-ring would require. Results depend on three things: a rubber compatible with the fluid, an undamaged sealing face and the right size.

Q: Are Dowty seals better than crush washers?

A: Neither is better in every joint, because they seal in different ways. A crush washer deforms permanently under high torque, which is why it is normally treated as single use, whereas a Dowty seal relies on elastic compression of the rubber, with the steel ring setting the limit, so it seals at lower torque. Metal crush washers have the advantage at high temperatures and with fluids that attack nitrile.

Q: Are Dowty washers better than copper washers?

A: It depends on the fluid and the temperature. Dowty washers seal at lower torque and suit oil, fuel and air systems that run within nitrile's limits. Copper washers tolerate far higher temperatures and fluids such as glycol-based brake fluid, which is why copper is the usual choice on brake banjo bolts and the better option for those applications.

Q: Is a bonded washer the same as a Dowty seal?

A: Yes. The design was originally made by the Dowty Group, and the name has stuck as the everyday term for bonded seals from any manufacturer. Catalogues also list the same component as a bonded washer, bonded seal washer or bonded rubber washer: a steel ring with a rubber seal bonded to its inner edge.

Q: What size bonded washer do I need?

A: Match the washer to the nominal diameter of the thread, so an M12 plug or fitting takes an M12 bonded washer. Then check that the external diameter fits the spot face around the port and that the face of the plug or fitting covers the rubber and seats on the steel ring. On self-centring designs the internal diameter is smaller than the thread, so it is not a guide to size.

Bespoke Dowty Washers Manufacture.

High precision, bespoke manufacture of Dowty Washers to customer specification. State of the art facilities specialising in both small batch prototyping and large scale manufacture.

Get A Quote

Your Browsing History.

Looks Like You're In Looks Like You're Outside

To get accurate pricing, stock, and delivery, please use the Accu site.

We can only deliver within the region you select.

Check Your Region

To get accurate pricing, stock, and delivery, please use the correct Accu Site for your region.